ZACplus Citizen-Science Workshop vom 03.07.2026: Unterschied zwischen den Versionen

Aus Open Source Ecology - Germany
Zur Navigation springen Zur Suche springen
(Die Seite wurde neu angelegt: „== Online-Workshop vom 03.07.2026, Printing the 3d-printable parts == Print the 3D-printable parts with PLA . This are the endplates (one with and one without…“)
 
 
(3 dazwischenliegende Versionen desselben Benutzers werden nicht angezeigt)
Zeile 2: Zeile 2:
  
 
Print the 3D-printable parts with PLA . This are the endplates (one with and one without hole) and we make a stencil for punching-holes for the metal-plates, in case we produce them manually instead of milling them.
 
Print the 3D-printable parts with PLA . This are the endplates (one with and one without hole) and we make a stencil for punching-holes for the metal-plates, in case we produce them manually instead of milling them.
 +
 +
=== Endplates ===
 +
 +
 +
==== Endplate with Hole ====
 +
 +
<gallery widths="800" heights="600" perrow="2>
 +
File:Endplate_with_hole.jpg
 +
</gallery>
 +
 +
 +
 +
 +
==== Endplate with pin ====
 +
 +
<gallery widths="800" heights="600" perrow="2>
 +
File:Endplate_with_pin.jpg
 +
</gallery>
 +
 +
 +
 +
=== Stencils ===
 +
 +
 +
==== Stencil for Grafoil ====
 +
 +
<gallery widths="800" heights="600" perrow="2>
 +
File:Grafoil.jpg
 +
</gallery>
 +
 +
 +
 +
==== Stencil for Brass- and Copper-plate ====
 +
 +
Here are very small holes in it which help marking the exact middle of a bigger hole, but are small enough to to can be used with a scriber without any margin (and therefore delivers the exact point).
 +
 +
<gallery widths="800" heights="600" perrow="2>
 +
File:Brasscopper.jpg
 +
</gallery>
 +
 +
 +
 +
==== Stencil for Silicone-Gasket ====
 +
 +
Here i have simply used the Model for the static frame. When using it as a stencil its maybe a good idea to print it with a thickness of only 1 mm or less.
 +
 +
<gallery widths="800" heights="600" perrow="2>
 +
File:Silicone.jpg
 +
</gallery>

Neueste Überarbeitung vom 13. Oktober 2026, 17:28 Uhr

Online-Workshop vom 03.07.2026, Printing the 3d-printable parts

Print the 3D-printable parts with PLA . This are the endplates (one with and one without hole) and we make a stencil for punching-holes for the metal-plates, in case we produce them manually instead of milling them.

Endplates

Endplate with Hole

  • Endplate with hole.jpg



Endplate with pin

  • Endplate with pin.jpg


Stencils

Stencil for Grafoil

  • Grafoil.jpg


Stencil for Brass- and Copper-plate

Here are very small holes in it which help marking the exact middle of a bigger hole, but are small enough to to can be used with a scriber without any margin (and therefore delivers the exact point).

  • Brasscopper.jpg


Stencil for Silicone-Gasket

Here i have simply used the Model for the static frame. When using it as a stencil its maybe a good idea to print it with a thickness of only 1 mm or less.

  • Silicone.jpg
Abgerufen von „https://wiki.opensourceecology.de/index.php?title=ZACplus_Citizen-Science_Workshop_vom_03.07.2026&oldid=25933“ (Montag, den 19.10.2026)